Alternative Fuels

Hello, I came across your post about dual curve boxes, it seems to me that you can also use the MSD dual curve box #40622 (http://www.dualcurve.com/frm22827.pdf) and to my knowledge you can use a MSD muliple spark box together with the dual curve box, to upgrade your spark and combustion proces. I h...

I allways make thies plates myself from stainless steel, they do the trick and NOT the block-off plates you find std. in a gasket headset.
I make the hole in the gasket a bit larger so the stainless steel plate is covering the hole completely.
Nook

hello Franz,
thanks for your reply, but I have a 12 volt exhaust analyzer that I can take with me on the passender seat, how about that!!
greetings,Nook
ps. still reading your book, great!!

Thanks Frank, I,m always a bit cautious with leaning-out on the LPgasfuel, my experience tell's me that always keep a LPgas feuled engine a bit at the rich side of middle. The cat. is all ready gone and the 425 carburator is a non FB one, so I think that I,m going to try both way's (with and without...

hello propane friends I,m propaneing a 8.2 ltr. 1976 cadillac, I,m useing a Impco 425 mixer directly build to the manifold without a gasoline carb. There is a EGR valve on this engine, and I,m wondering if I leave it in function (if it's working??) or take it off and block the hole with a plate. I k...

Thanks for your replay's Franz and Steptoe I drive a 1969 chevrolet C20 pick up truck as a daily driver, It has a 366 truck engine with a 9.5:1 compression and a 255 degr camshaft and light dome pistins (GM.special LP Gas Pistons for this engine) The LpGas setup is a model E,with a 425 mixer direct ...

I,ve learned that the total advance timing should not be higher than +/- 30 degrees, but the Impco-beru tech guy's want me to believe someting different. Did I miss something at my LPGas education :roll: Here it is; ------------------------------------------------------------------------------------...

Hello,
Can somebody please thell me what a 300A-M mixer is,can't find them
in the Impco manuals or in the Diagnostic guide from Franz.
Are they the same as 50 and 70 series???
any info is welcome!!

Thanks

Thanks for helping me out on this one.
greetings from Holland,
Nico

So if I understand correctly, there is no need for a electric valve build in the vac hose between the vaporizer and the 425 mixer. And wat if the vac hose is direkt conected to the manifold? does it needs a electric valve to cut the gas stream or is this done in the vaporizer by the the build in sol...

Thanks for your reply! I all ready have a vac. hose ( 3/8 ) between the vaporizer and 425 mixer,with an 12 volt valve in between,that I use it the moment I start the engine and turn it off asa the engine runs,it helps a litlle I'm going the try the E-BS vaporizer and let you know how this works out....

Thanks guy's for your answers!! I bought one E-BS new and I like to use it on my Pick Up truck that has a chevrolet V8 366 ci. truck engine in it and a TH 400 auto. 411:1 end gears. It's also carry's have loods some times and has to work real hard. I use a model E now,with a SA. but it's starts not ...

hello LP Gas colleagues,
can somebody please explain the difference between model E and a model EBS and how they operate

thanks

hello,
can I have a list of the parts you like to sell
thanks

Thanks for your reply,Frank's Raso Enterprises charge also $20. but the
shipping cost from the States to the Netherlands is much cheaper than
from Canada to the Netherlands.
Thanks Again,Nook.